NJM2902 JRC供应及NJM2902技术文档
欢应来电洽谈NJM2902的相关信息!
NJM2902 包括 四独立高赢利操作放大器那是设计为 唯一供应操作。
NJM2902,在它的静态状态(没有和产品情况),当设计, QU被偏心由恒定的潮流(划分射线), QL停留。While使用与两电源方式,天桥distortion也许立即发生,当QL。There也许是盒,当应用音频放大器的signals,不仅畸变,而且卓越地变窄的明显的频率带宽。It比装载潮流是可调整的,特别是当使用电源方式,经常使用与在QU的更高的潮流(包括反馈潮流)时,然后联络下拉的抵抗者RP在产品和GND别针之间的部分。
NJM2902
QUAD SINGLE-SUPPLY OPERATIONAL AMPLIFIER
■ GENERAL DESCRIPTION ■ PACKAGE OUTLINE
The NJM2902 consists of four independent high-gain operational amplifiers that are designed for single-supply operation.
Operation from split power supplies is also possible and the low power supply drain is independent of the magnitude of the
power supply voltage.
Used with a dual supply the circuit will operate over a wide range of supply voltages. However, a large amount of crossover distortion may occur with loads to ground. An external current-sinking resistor to-VS will reduce crossover distortion. There is no crossover distortion problem in single-supply operation if the load is direct-coupled to ground.
■ FEATURES
● Single Supply
● Operating Voltage ( +3V~+30V )
● High Output Voltage ( V+-2V )
● Slew Rate ( 0.5V/µs typ. )
● Low Operating Current ( 1mA typ. )
● Package Outline DIP14,DMP14,SSOP14
● Bipolar Technology
■ PIN CONFIGURATION
NJM2902N NJM2902M
NJM2902V
PIN FUNCTION
1.A OUTPUT 8.C OUTPUT
2.A –INPUT 9.C -INPUT
3.A +INPUT 10.C +INPUT
4.V+ 11.GND
5.B +INPUT 12.D +INPUT
6.B –INPUT 13.D -INPUT
7.B OUTPUT 14.D OUTPUT
NJM2902N
NJM2902M NJM2902V
■ EQUIVALENT CIRCUIT ( 1/4 Shown )
Ver.2003-03-20
-1-
NJM2902
■ ABSOLUTE MAXIMUM RATINGS
( Ta=25˚C )
|
PARAMETER |
SYMBOL |
RATINGS |
UNIT |
|
Supply Voltage |
V+(V+/V-) |
32 ( or ± 16 ) |
V |
|
Differential Input Voltage |
VID |
32 |
V |
|
Input Voltage |
VIC |
-0.3~+32 |
V |
|
Power Dissipation |
PD |
( DIP14 ) 570 ( DMP14 ) 300 ( SSOP14 ) 300 |
mW |
|
Operating Temperature Range |
Topr |
-40~+85 |
˚C |
|
Storage Temperature Range |
Tstg |
-50~+125 |
˚C |
■ ELECTRICAL CHARACTERISTICS
( Ta=25˚C,V+=5V )
|
PARAMETER |
SYMBOL |
TEST CONDITION |
MIN. |
TYP. |
MAX. |
UNIT |
|
Input Offset Voltage Input Offset Current Input Bias Current Large Signal Voltage Gain Maximum Output Voltage Swing Input Common Mode Voltage Range Common Mode Rejection Ratio Supply Voltage Rejection Ratio Output Source Current Output Sink Current Channel Separation Operating Current Slew Rate Gain Bandwidth Product |
VIO IIO IB AV VOM VICM CMR SVR ISOURCE ISINK CS ICC SR GB |
RS=0Ω I +-I - IN IN I + or I - IN IN RL>2kΩ RL=2kΩ VIN+=1V,V -=0V IN VIN+=0V,V -=1V IN f=1k~20kHz,Input Referred RL=∞ V+/V-=±15V V+/V-=±15V |
- - - - 3.5 0~3.5 - - 20 8 - - - - |
2 5 20 100 - - 85 100 40 20 120 1 0.5 0.5 |
10 50 500 - - - - - - - - 2 - - |
mV nA nA V/mV V V dB dB mA mA dB mA V/µs MHz |
- 2 - Ver.2003-03-20
NJM2902
■ TYPICAL CHARACTERISTICS
Ver.2003-03-20
- 3 -
NJM2902
■ TYPICAL CHARACTERISTICS
- 4 - Ver.2003-03-20
NJM2902
■ TYPICAL CHARACTERISTICS
Ver.2003-03-20
- 5 -
NJM2902
■ APPLICATION
Improvement of Cross-over Distortion
Equivalent circuit at the output stage NJM2902,in its static state ( No in and output condition ) when design, QU being biassed by constant current ( break down beam ) yet, QL stays OFF.
While using with both power source mode, the cross-over
distortion might occur instantly when QL ON.
There might be cases when application for amplifier of audio
signals, not only distortion but also the apparent frequency bandwidth being narrowed remarkably.
It is adjustable especially when using both power source mode, constantly to use with higher current on QU than the load current ( including feedback current ),and then connect the pull-down resister RP at the part between output and GND pins.

